Description
Product Description
Rovmaker Ip68 Plug Socket 2 Pin Connector With Male and Female Industrial Plug and Socket
- Small volume and lightweight, small footprint, professional wet plug.
- High seawater corrosion-resistant stainless steel shell material.
- Standard pin and hole position distribution, 7/16″-20 UNF tail thread, can be exchanged with different brands of the same model.
Dimensions Detail
Specification
|
STRUCTURE
|
MATERIALS AND SPECIFICATIONS
|
|
Main
|
The seawater corrodes stainless steel
|
|
Install screw
|
7/16-20 UNF thread length is 15/19mm
|
|
Socket head
|
Neoprene (special mixing rubber for underwater connector)
|
|
Contact Pin
|
Gold-plated copper alloy, American standard pin
|
|
Positioning pin
|
303 stainless steel (2 needle Ø 3.2, 3/4 needle Ø 2, 5/6/8 needle don’t need)
|
|
O-rings
|
Nitrile rubber, the imported o-rings, parker 2-014, Ø 12.42 x 1.78
|
|
Locking lid
|
Polyformaldehyde resin (POM)
|
|
Cable plug body
|
Special polyether
|
|
Install line
|
Teflflon, silver-plated pure copper.
|
|
End cap
|
Neoprene (special mixing rubber for underwater connector)
|
|
Cable plug
|
Pressure-resistant seawater special cable.
|
TECHNICAL PERFORMANCE
|
ITEM
|
RATING VALUE
|
|
Depth
|
0~1000 meters
|
|
Voltage
|
300V (resistance to voltage is greater than 1500V 60s)
|
|
Working current
|
2A~16A
|
|
Insulation resistance
|
> 1000 m Ω (room temperature)
|
|
Wet insertion frequency
|
> 500 times
|
|
Working temperature
|
(-4~60)°C
|
Pre-cautions
*Always apply grease before mating.
* Disconnect by pulling straight, not at an angle.
* Disconnect by pulling straight, not at an angle.
* Do not pull on the cable and avoid sharp bends at cable entry.
* When using a bulkhead connector, ensure that there are no angular loads.
* All kinds of connectors should not be exposed to extended periods of heat or direct sunlight.
* When using a bulkhead connector, ensure that there are no angular loads.
* All kinds of connectors should not be exposed to extended periods of heat or direct sunlight.
Greasing and mating above water (dry mate) :
* Connectors must be greased with Molykote 44 Medium(recommended brand) before every mating.
* A layer of grease corresponding to a minimum 1/10 of socket depth should be applied to the female connector.
* The inner edge of all sockets should be completely covered, and a thin transparent layer of grease left visible on the face of the connector.
* After greasing, fully mate the male and female connector in order to secure optimal distribution of grease on pins and in sockets.
* To confirm that grease has been sufficiently applied, de-mate, and check for grease on every male pin. Then re-mate the connector.
Greasing and mating underwater (wet mate) ：
* Connectors must be greased with Molykote 44 Medium(recommended brand) before every mating.
* A layer of grease corresponding to approximately 1/3 of socket depth should be applied to the female connector.
* All sockets should be completely sealed, and a transparent layer of grease left visible on the face of the connector.
* After greasing, fully mate the male and female connector and remove any excess grease from the connector joint.
Cleaning
* General cleaning and removal of any accumulated sand or mud on a connector should be performed using spray based contact cleaner (isopropyl alcohol).
* New grease must be applied again prior to mating.
Use of Loctite
* For locking metallic connectors, the use of Loctite 243 is recommended.
Installation Requirements
- End surface roughness requirements Ra1.6 in the diameter of the screw hole around 25mm when threaded hole installation.
- Hole diameter should be between Ø 11.2 ~ Ø11.4 mm and roughness requires Ra1.6 in the diameter of the screw hole around 25mm when through-hole installation.
- Before installing, make sure to apply a thin layer of silicone oil to the o-ring, not too thick.
More Pins
Reviews
There are no reviews yet.